The "Stroke of genius" project in the March 2009 issue of BeadStyle includes a beautiful design alternative that combines braided WireLace with aquiline crystals. Designer Linda Arline Hartung sent the following instructions:

Four strands of WireLace get these big-holed beads to behave. Make an overhand knot between each group of crystals. The WireLace will fill the large bead holes and the knots keep the crystals tight to each other forcing them to the juxtaposed positions. Finish with a four-strand braid to the desired length, glue into a bell end cap and add a teardrop clasp set with a coordinating crystal.


1: Take two yards (1.8 m) of 2.5mm WireLace and two yards (1.8 m) of 6mm WireLace. Center a pearl needle on both strands.

2: String on all crystals as shown in the photo. Cut ends at pearl needle to remove.needle and create four 36 in.(.9 m) strands.

3: Center the large bead on the four WireLace strands.

4: Group the center cluster and make one overhand knot (Basics) next to cluster with all four strands of the WireLace. On opposite side tighten up all the crystals in that cluster and make another overhand knot. This knot must be very tight and snug next to the crystals to force them to keep their position.

5: Push the next cluster of crystals to the center and make another overhand knot with the WireLace - each time making sure the knots are tight to and snug to the crystals. Continue on each side until all the clusters are complete.

6: On each side, after the last overhand knot, separate out the four strands of WireLace to do a four-strand braid.

How to do a four-strand braid:
1) Divide into two sections with a 2.5 mm and 6 mm on each side.
2) Pick up a strand on the ‘outside’  and wrap it under two strands and over one strand. Repeat on the opposite side – always using the outside strand.

7: Continue braiding about 1 in. (2.5 cm) past the desire length on either side and clamp the ends to keep the braid from loosening or coming apart. Use whatever you have handy – tie a string around the end – or use a bead stopper or paper clip, etc.

8: Determine the final desired length and where the braid will end. To keep the braid from coming apart and to make it easier to glue into the end caps, mix 2-part epoxy and apply it directly onto the WireLace braid beginning about ¼ in. (.25 cm )from the desired end. When the epoxy dries,  cut the WireLace braid on the glued area with a wirecutters so that you have a glued-end ‘nub’. Test to make sure the braid nub fits in the bell end cap. If not, gently roll end between finds to reshape the braid making it round to fit.

9: Mix 2-part epoxy and fill end caps half full and push over braid nub ends – you should see a small rim of glue seep out. If not quickly pull off the bell end cap and add more glue. Let dry.

10: Attach teardrop clasp by rotating split ring on the bell end caps with a chainnose pliers. Squeeze closed.

Supplies

 necklace 19 in. (48 cm)
◆    36 mm aquiline crystal, top drilled, color A
◆    28 mm aquiline crystal, top drilled,  color C,
◆    28 mm aquiline crystal, center drilled, color B
◆    6 18 mm aquiline crystals, top drilled, 2 color A, 1 color C, 3 color B
◆    8 18 mm aquiline crystals, center drilled, 4 color A,
4 color C
◆    6 18 mm polygon crystals, color B
◆    two yards (1.8 m) 2.5mm WireLace
◆    two yards (1.8 m) 6mm WireLace
◆    2 4 mm bell end-caps
◆    2 7 mm split rings
◆    box clasp
◆    chainnose pliers
◆    diagonal wire cutters
◆    two-part epoxy
◆     2 toothpicks (for mixing and applying glue), sticky note pads (for mixing glue on), isopropyl alcohol for cleaning up excess glue if needed.
◆    scissors (for cutting WireLace).
◆     fine/lightweight collapsible-type pearl needle

 CRYSTALLIZED colors:
    Color A: crystal
    Color B: black diamond
    Color C: jet